It has optional daughter boards like 8051, PIC, AVR, ARM, Microchip PIC16F877/16F876/16F84, Motorola 68HC11, Spartan II, Spartan III, Spartan VI, CPLD etc.
It has level microcontroller 8051 family processor to enable it to upload and download program to various other 8,16 ,32 bit microcontrollers
It has a Serial/Parallel/USB (JTAG) link which enable user to communicate with PC.
User can develop the circuit using different Software and any development tool for design available in the world.
It has I/O counter interface to enable it to connect various demo modules. This helps in man to machine interface.
Two 50 pin headers provided for interfacing daughter boards.
Has a general purpose areas on board to enable it to incorporate additional circuit.
Peripheral Features for 8051
On-chip Flash Program Memory with In-System Programming (ISP) and In-Application Programming (IAP) capability
Can be programmed by the end-user application (IAP)
6-clock/12-clock mode Flash bit erasable and programmable via ISP
6-clock/12-clock mode programmable “on-the-fly” by SFR bit
Peripherals (PCA, timers, UART) may use either 6-clock or
12-clock mode while the CPU is in 6-clock mode
Speed up to 20 MHz with 6-clock cycles per machine cycle (40 MHz equivalent performance); up to 33 MHz with 12 clocks per machine cycle
Fully static operation
Four interrupt priority levels
Seven interrupt sources
Four 8-bit I/O ports
Full-duplex enhanced UART
Framing error detection
Automatic address recognition
Power control modes
Clock can be stopped and resumed
Idle mode
Power down mode
Programmable clock-out pin
Second DPTR register
Asynchronous port reset
Low EMI (inhibit ALE)
Programmable Counter Array (PCA)
PWM
Capture/Compare
ON-BOARD INTERFACES
16×2 LCD module
Six Seven Segment Displays
Stepper Motor Controller Interface
8×8 LED Matrix Display
EWSN Status LED’s 12 Nos.
ADC/DAC Interface
RS-232 interface
USB interface
Four Data Switches
Switch Array
AT24C16 Serial EEPROM
4×4 Keyboard
Power Indicator LED
Bluetooth Interface
GSM Interface
Zigbee Interface
DAUGHTER BOARDS:
1. Board for Atmel 8051
With this board you can develop and prototype with any of 8051 (AT89S51, AT89S52, P89V51RD2, AT89Cxx) 40 pin microcontrollers. The board have and status LED. The 1.5 Amp bridge rectifier allow this board to be powered with both AC and DC power supply adapters. Board having USB port for flashing P89V51RD2 (NXP) microcontroller. There is 5V, 12V, GND power bus which allow to power external peripherals module.
FEATURES:
DIP40 microcontroller socket.
Quartz crystal 11.05892 Mhz.
USB Interface for communication with PC.
Reset button.
ON – OFF switch.
Power plug-in jack.
Extension slot on every uC pin.
GND bus.
Vcc bus.(5V and 12V).
On board power indication.
Two 50 pin headers provided for interfacing with main board.
2. Board for Microchip PIC16F84
With this board you can develop and prototype with Microchip PIC16F84 microcontrollers. The board have and status LED. The 1.5 Amp bridge rectifier allow this board to be powered with both AC and DC power supply adapters. Board having USB port for downloading sample programs. There is 5V, 12V, GND power bus which allow to power external peripherals module.
FEATURES:
DIP microcontroller socket.
USB Interface for communication with PC.
Reset button.
ON – OFF switch.
Power plug-in jack.
Extension slot on every uC pin.
GND bus.
Vcc bus.(5V and 12V).
On board power indication.
Two 50 pin headers provided for interfacing with main board.
High Performance RISC CPU:
Only 35 single word instructions to learn
All instructions single cycle except for program branches which are two-cycle
Operating speed: DC – 20 MHz clock input
DC – 200 ns instruction cycle
1024 words of program memory
68 bytes of data RAM
64 bytes of data EEPROM
8-bit wide data bytes
14-bit wide instruction words
15 special function hardware registers
Eight-level deep hardware stack
Direct, indirect and relative addressing modes
Four interrupt sources:
External RB0/INT pin
TMR0 timer overflow
PORTB<7:4> interrupt on change
Data EEPROM write complete
Peripheral Features:
13 I/O pins with individual direction control
High current sink/source for direct LED drive
25 mA sink max. per pin
25 mA source max. per pin
TMR0: 8-bit timer/counter with 8-bit programmable prescaler
Board for Microchip P16F877
With this board you can develop and prototype with Microchip PIC16F877 microcontrollers. The board have and status LED. The 1.5 Amp bridge rectifier allow this board to be powered with both AC and DC power supply adapters. Board having USB port for downloading sample programs. There is 5V, 12V, GND power bus which allow to power external peripherals module.
FEATURES:
DIP40 microcontroller socket.
Quartz crystal 4 Mhz.
USB Interface for communication with PC.
Reset button.
ON – OFF switch.
Power plug-in jack.
Extension slot on every uC pin.
GND bus.
Vcc bus.(5V and 12V).
On board power indication.
Two 50 pin headers provided for interfacing with main board.
High Performance RISC CPU:
Only 35 single word instructions to learn
All instructions single cycle except for program branches which are two-cycle
Operating speed:
DC – 20 MHz clock input
DC – 200 ns instruction cycle
Up to 8K x 14 words of FLASH Program Memory, Up to 368 x 8 bytes of Data Memory (RAM), Up to 256 x 8 bytes of EEPROM Data Memory
Peripheral Features:
Timer0: 8-bit timer/counter with 8-bit prescaler
Timer1: 16-bit timer/counter with prescaler, can be incremented during SLEEP via external crystal/clock
Timer2: 8-bit timer/counter with 8-bit period register, prescaler and postscaler
Two Capture, Compare, PWM modules
Capture is 16-bit, max. resolution is 12.5 ns
Compare is 16-bit, max. resolution is 200 ns
PWM max. resolution is 10-bit
Synchronous Serial Port (SSP) with SPI™ (Master mode) and I2C™ (Master/Slave)
Parallel Slave Port (PSP) 8-bits wide, with external RD, WR and CS controls (40/44-pin only)
Brown-out detection circuitry for Brown-out Reset (BOR)
Analog Features:
10-bit, up to 8 channel Analog-to-Digital Converter (A/D)
Brown-out Reset (BOR)
Analog Comparator module with:
Two analog comparators
Programmable on-chip voltage reference (VREF) module
Programmable input multiplexing from device inputs and internal voltage reference
Comparator outputs are externally accessible
4. Board for Microchip P18F455
With this board you can develop and prototype with Microchip PIC18F455 microcontrollers. The board have and status LED. The 1.5 Amp bridge rectifier allow this board to be powered with both AC and DC power supply adapters. Board having USB port for downloading sample programs. There is 5V, 12V, GND power bus which allow to power external peripherals module.
FEATURES:
DIP40 microcontroller socket.
Quartz crystal 11.05892 Mhz.
USB Interface for communication with PC.
Reset button.
ON – OFF switch.
Power plug-in jack.
Extension slot on every uC pin.
GND bus.
Vcc bus.(5V and 12V).
On board power indication.
Four mounting holes 3.0 mm for easy mounting.
Two 50 pin headers provided for interfacing with main board.
Peripheral Features:
High-Current Sink/Source: 25 mA/25 mA
Three External Interrupts
Four Timer modules (Timer0 to Timer3)
Up to 2 Capture/Compare/PWM (CCP) modules:
Capture is 16-bit, max. resolution 5.2 ns (TCY/16)
Compare is 16-bit, max. resolution 83.3 ns (TCY)
PWM output: PWM resolution is 1 to 10-bit
Enhanced Capture/Compare/PWM (ECCP) module:
Multiple output modes
Selectable polarity
Programmable dead time
Auto-shutdown and auto-restart
Enhanced USART module:
LIN bus support
Master Synchronous Serial Port (MSSP) module Supporting 3-Wire SPI (all 4 modes) and I2C™ Master and Slave modes
10-Bit, Up to 13-Channel Analog-to-Digital Converter
(A/D) module with Programmable Acquisition Time
Dual Analog Comparators with Input Multiplexing
5. Board for PIC J24 Series
With this board you can develop and prototype with Microchip microcontrollers. The board have and status LED. The 1.5 Amp bridge rectifier allow this board to be powered with both AC and DC power supply adapters. Board having USB port for downloading sample programs. There is 5V, 12V, GND power bus which allow to power external peripherals module.
FEATURES:
USB Interface for communication with PC.
Reset button.
Extension slot on every µC pin.
GND bus.
Vcc bus.(5V and 12V).
Two 50 pin headers provided for interfacing with main board.
6. Board for Motorola 68HC11
With this board you can develop and prototype with Motorola 68HC11 microcontrollers. The board have and status LED. The 1.5 Amp bridge rectifier allow this board to be powered with both AC and DC power supply adapters. Board having Serial port for downloading sample programs. There is 5V, 12V, GND power bus which allow to power external peripherals module.
7. Board for ATMEGA 328
With this board you can develop and prototype with ATMEGA 328 microcontrollers. The board have and status LED. The 1.5 Amp bridge rectifier allow this board to be powered with both AC and DC power supply adapters. Board having USB port for downloading sample programs. There is 5V, 12V, GND power bus which allow to power external peripherals module.
FEATURES:
Microcontroller socket.
Quartz crystal 6 Mhz.
USB Interface for communication with PC.
Reset button.
Extension slot on every uC pin.
GND bus.
Vcc bus.(3.3 V,5V and 12V).
On board power indication.
Two 50 pin headers provided for interfacing with main board.
8. Board for ATMEGA 16
With this board you can develop and prototype with ATMEGA 16 microcontrollers. The board have and status LED. The 1.5 Amp bridge rectifier allow this board to be powered with both AC and DC power supply adapters. Board having USB port for downloading sample programs. There is 5V, 12V, GND power bus which allow to power external peripherals module.
FEATURES:
Microcontroller socket.
Quartz crystal 8 Mhz.
USB Interface for communication with PC.
Reset button.
Power plug-in jack.
Extension slot on every uC pin.
GND bus.
Vcc bus.(5V and 12V).
On board power indication.
Four mounting holes 3.0 mm for easy mounting.
Two 50 pin headers provided for interfacing with main board.
9. Board for ARM 2148
With this board you can develop and prototype with ARM7 2148 microcontrollers. The board have and status LED. The 1.5 Amp bridge rectifier allow this board to be powered with both AC and DC power supply adapters. Board having USB port for downloading sample programs. There is 5V, 12V, GND power bus which allow to power external peripherals module.
FEATURES:
Microcontroller socket.
USB Interface for communication with PC.
Extension slot on every uC pin.
GND bus.
Vcc bus.(5V and 12V).
Two 50 pin headers provided for interfacing with main board.
10. Board for STM 32
This is a Board for ARM Microcontroller STM32F103C8T6. Board is suitable for learners that want to learn STM32 microcontroller with ARM Cortex-M3 32-bit core.
FEATURES:
Based on: STM32 Based
Core Architecture: ARM
Core Sub-Architecture: Cortex-M0+
Silicon Core Number: STM32G070RBT6
of Bits: 32bit
Two 50 pin headers provided for interfacing with main board.
11. ARM Cortex M3 Daughter Board
FEATURES:
Based on LPC 1768
All ports are available onboard for the user
USB Programming
On board USB for Downloading
Two 50 pin headers provided for interfacing with main board.
12. Board for FPGA Spartan-3
With this board you can develop and prototype with FPGA Spartan3 microcontrollers. The board have and status LED. The 1.5 Amp bridge rectifier allow this board to be powered with both AC and DC power supply adapters. Board having USB port for downloading sample programs. There is 5V, 12V, GND power bus which allow to power external peripherals module.
Core3S250E is an FPGA board that features an XC3S250E device onboard, supports further expansion.
FEATURES:
Onboard 1pcs XCF02S
Integrated FPGA basic circuit, such as clock circuit
Onboard n CONFIG button, RESET button
All the I/O ports are accessible on the pin headers
Onboard JTAG debugging/programming interface
Two 50 pin headers provided for interfacing with main board.
13. Board for CPLD
FEATURES:
It uses industry standard CPLD 95C108 or 95C72
It communicates with computer through standard Webpack
User can develop the circuit/schematic using Xilinx standard Foundation Series software and any Development tool for VLSI design available in the world
All the I/O ports are accessible on the pin headers
Onboard JTAG debugging/programming interface
Two 50 pin headers provided for interfacing with main board.
14. Board for FPGA Spartan-6
FEATURES:
FPGA: Spartan-6 XC6SLX9 in TQG144 package
Flash memory: 16 Mb SPI flash memory (M25P16)
100MHz CMOS oscillator
USB 2.0 interface for On-board flash programming
FPGA configuration via JTAG and USB
IOs for user-defined purposes
Onboard voltage regulators for single power rail operation
Two 50 pin headers provided for interfacing with main board.
15. Board for Raspberry PI BOARD
With this board you can develop and prototype with Raspberry Pi microcontrollers. The board have and status LED.
The Raspberry Pi 4 has a quad-core ARM Cortex-A72 processor, 2.4 GHz and 5.0 GHz Wi-Fi, Bluetooth 5.0, and gigabit Ethernet. It also has two micro-HDMI ports, two USB 3.0 ports, and two USB 2.0 ports.
All ports are available onboard for the user
Two 50 pin headers provided for interfacing with main board.
16. Board for MSP430F540X
The MSP-EXP430F5529LP includes the MSP430F5529 16-bit MCU with 128KB Flash, 8KB RAM, up to 25MHz CPU speed, integrated USB 2.0 PHY, 12-bit analog-to digital converter (ADC), timers, serial communication (UART, I2C, SPI) .
USB Interface for communication with PC.
Reset button.
Two 50 pin headers provided for interfacing with main board.
.jpg "Universal Embedded-VLSI Trainer (VPL-ET) Manufacturers in New Delhi")
